rcl57100.exe CL57 Reference Disk v1.00 (zipped image)
rcl57102.zip CL57 Reference Disk v1.02 (zipped image)
CL57_Drivers.zip CL57 Device drivers (zipped image)
192-073 IBM PS/2 Model CL57 SX System And Features (8554-045)
ZG92-0165 IBM PS/2 Model CL57 SX System 8554-A45 and Features
S10G4419 IBM PS/2 Model CL57 SX HMR
S10G4420 IBM PS/2 Model CL57 SX HMS
8554_HMM 8554 Section of TPVOL1.PDF
8554 Numeric Error Codes
Install 387SX Math Co-Processor
Hard Drives for 8554
System Status Indicators
8554 Planar 07G1371
Note: On system board EC level C81806A,
J2 and J12 have been removed, and the cable between J2 and Voltage Converter
(index 19) is not used.
|1 System Expansion Connector
2 Display Control Card
3 Serial Connector
4 I/O Panel (Parallel/External
5 Indicator Card
6 Password-Override Connector
7 Backup Battery
8 Communication Interface
| 9 Diskette Drive
10 Thermal Sensor
11 Hard Disk Drive
12 Trackball/Keyboard Card
13 Dew Point Sensor
14 Voltage Converter
15 Voltage Converter
Peter rains on my parade:
The standard 2MB that each CL57 comes with is a 2MB /
72-pin SIMM 80nS (similar to those from a 20MHz 8570) in a socket on the
rear side of the planar.I think it is the very same silly Low-Power CMOS
chips that the L40SX used. Back then I'd tried to use a bigger / other
module but all attempts ended in 2MB usable, no matter what I'd tried.
I think the BIOS has just the one 2MB type included and nothing else. Memory
expansion is done solely with these JEIDA cards.
IBM IC DRAM Cards
2MB IC DRAM Card P/N 07G1419
4MB IC DRAM Card P/N 07G1420
8MB IC DRAM Card P/N 07G1421
Peter blows smoke by saying:
CL57SX uses an internal 2MB module and does not accept
anything else there - apart from the fact that you will have to disassemble
the entire machine to reach that module.
There are two JEIDA memory card module slots at the right
- covered by the "internal modem slot cover" (you need to pull that cover
*out* to see the two JEIDA slots). JEIDA cards look like PCMCIA cards but
have staggered pins. PCMCIA have 2 parallel rows of pins.
8MB Memory Cards
John Johnson says: The CL-57 takes the same cards as a 750 laptop.
(CL57 & TP-750) [Kingston]
4MB Credit Card KTM-TP750/4 (92G7238, 07G1420,
8MB Credit Card KTM-TP750/8 (92G7241, 07G1421,
The CL57 has a minimum of 2MB installed. You can use 2,4
and 8MB IC DRAM cards to expand the memory. However, only 16MB is useable.
If you use two 8MB IC DRAM cards, the system will only use 16MB.
Action on Memory Error
If a memory error occurs, the CL57 relocates system memory in
1MB blocks. If POST detects a memory error in the first 640KB of system
memory, the entire 1MB of memory is deactivated and an error code is displayed.
Power off system
Remove KB and top cover
Install jumper over identified pins
Power on, leave jumper on until POST ends.
Power down and remove jumper.
Note: Unlike later systems, you
must remove the jumper after clearing the password, or you cannot set a
new power on password. Although that might not be too bad after all.
Peter leads off with:
10.4-inch Thin Film Transistor (TFT) Color LCD with 640
by 480 Video Graphic Array (VGA) resolution. Simultaneous LCD and CRT (eight
dots) display is supported.
The VGA with LCD controller supports a max of 720x400
(external display) or 640x480 (LCD) in text mode, and 640x480 (both external
and LCD) in graphics mode. The VGA with LCD controller is capable of displaying
256 colors at once. Composite video is not supported.
If the display has a permanent vertical red line when
powered on, it's probably a fine-short within the displays' driver section.
These displays were known for "solder beads contamination".
The CL57SX has a three-color "I" (red) "B" (green) "M" (blue) badge.
The keyboard is made by Lexmark - as is the keyboard /
trackpoint controller board. It is a typical membrane keyboard but time
takes its toll. There are two permanent enemies of these type of keyboards:
oxydation and detoriation. The plastic stuff gets brittle and breaks. Simply
put it is what happened with both keyboards. The connectors aren't that
easy to install anyway and are permanently bended. The stuff is like thin
glass after 10+ years and the cracks go through the printed conductors
as well. Ooof.
I'm working on a solution. No easy fix I'd say. However:
taking the layers apart is fairly easy. Just remove the keyboard from the
machine, remove the metal fixing "rod" from it, turn it over and use a
flatblade screwdriver on the plastic hook in the center of the underside.
With it pressed back you should be able to slide the metal shield sideways
and pull it off.
You end up with 5 separate parts:
- the keycaps mechanism
- the top membrane layer
- an insulating sheet with holes
- the bottom membrane layer
- the metal stabilizer / shield
On inspection with an ohmmeter you find the failing connections
measuring from the key contacts towards the connector ends. I detected
no less than 3 missing links, all within the small part that connect the
keyboard to the controller board. The membrane area itself is in good condition
on both sheets.
Beware: the printed conducts on the plastic aren't very rigid. Trying
to use a glassfibre pen or sharper pencil eraser to clean them from oxydated
parts will erode them entirely !
My idea is to connect a thin flat-ribbon cable to the membrane connectors
with some sort of conductive glue. Then build some sort of "flat connector"
that fits inside the keyboard controller board connectors. Or remove that
crap at all and use some angled pinrow connector. Hmmm. Nothing for the
faint at heart or people that tend to get nervous very fast.
I wish I had kept the conductive silver paint I used to repair defoggers
on rear windows in my old cars ... must have thrown it away a decade ago.
HDs for 8554
Peter Wendt wrote:
The CL57 normally uses an 80MB drive (FRU 95F4708) and
this drive is also used in the N51SX / SLC (8551), if it hasn't got only
the 40MB drive (FRU 95F4707).
For a larger disk for your CL57 or N51, look for the Thinkpad
720/C 120 or 160 MB drives - however it appears as if the 240MB needs a
modified systemboard -by what reasons, it is probably an IDE-drive and
Note: The Battery Status indicator
does not turn on unless there is a battery installed.
IBM PS/2 Communications Cartridge II
o External expansion port provides connectivity to host
and LAN systems via the Communications Cartridge II that can accommodate
3270, 5250 emulation and Token-Ring half-size
adapters. The Communications Cartridge II uses a quick attach/detach
mechanism for connecting to the CL57 SX and requires no external power
IBM PS/2 Serial Adapter P/N 79F6800
IBM PS/2 Internal Data/Fax Modem P/N 94X2555
o The IBM PS/2 Internal Data/Fax Modem and IBM PS/2 Serial
Adapter optional features use the same internal connector, so only one
of these options can be installed per system.
IBM High Speed Internal Data/Fax Modem (P/N 42G2580) is a V.32bis Data
(300-14,400bps)/V.17 fax (300-14,400bps), internal modem. 192-261
Install Math Co-Processor
Unal Z put one in and said:
| Turn CL57 upside down. At the left rear corner, near the FDD,
there is a cover.
|| Insert the 386SX co-pro with it's beveled edge "A" pointed toward
the socket's beveled edge "B".
Ingenious, carefully lift the small plate (right-hand
or FDD side at the corner on the bottom) with a screwdriver. It pops up
and reveals the socket. Insert the tip of the screwdriver in the lid of
the plate, start sideways.
The machine came with a defective trackball - the "pickup
rollers" on the sensors were missing. I replaced them with cut-off pieces
from a wire insulation (silicon cable - 0.75mm inner diameter). Works fine
The trackballs suffer on several mechanical problems.
The little "sensor wheels" are pretty instable and if you treated that
thing a bit too hard the thin printboard carrying the sensors (photo-couplers)
will break off from the holders. The upper cover, fixing the ball, needs
to be set precisely and may not apply any kind of mechanical stress to
the ball itself.
The "inner" sides of the sensor-wheel axles are hanging
free and the opposite site sits into some sort of plastic holder ... it
seems as if they wear out after some time and the further guiding of the
axles in no longer given. This results in a trackball that works perfectly
left and right, but no longer up and down. I'd tried to fix the problem,
but had to time to experiment nay further.
The mechanical part of the trackball might be used from some
later Compaq laptops - or might be purchased from ALPS (if I remember
IBM PS/2 Miniature Mouse P/N 07G0033
Pointing device port for the IBM PS/2 Miniature Mouse,
or the external numeric keypad. The numeric keypad also has a pointing
device port to enable both numeric keypad and IBM PS/2 Miniature Mouse
The CL57 was originally a design for domestic japanese
/ asian markets. IBM had created the L40SX some time before as a cooperative
production between IBM Japan and the PS/2 division in Boca Raton. Logically
this caused a lot trouble (for example due to different working times and
time zones). When the L40 appeared on the market as a Notebook ... the
competitors had already announced Laptops - and color LCDs. The IBM Japan
development group had built a color laptop "just for fun" and presented
it to the IBM Management. They had planned to install the 486SX-processor
in the machine - but IBM management was afraid this were a too big competition
to the PS/2 series. They gave the okay to bring out the machine but only
with a smaller processor ... and so they changed it to have a 386SX. If
you look closer into the machines identification you will find a naming
"PS/55" - this is typical for originally IBM Japan products, which usually
have model numbers in the 55xx-range and not 85xx as PS/2 had. The
manufacturing plant-ID on the 8554 is -97- followed by the 7-digit serial
number. Plant 97 is the IBM Japan Entry Systems factory (forgot where it