8550 Tinkering

Gereon Wenzel:
   My 8550 has the old style 30M ESDI with the logic on the MCA card and the disk plugging straight to the MCA card. Now I got hold of a card looking similar but without logic with connector for the bigger (up to 160MB) ESDI with onboard logic. Thinking it's always a good idea to expand disk space, just swapped to my 8550 and connected a working 80MB ESDI. Hard disk change notice (never got on the 8570 when swapping ESDI), autoconfig, Disk spins down and up, system frozen.
Tried several times always same. switched back to the original 30MB.

Tony:
   50Z only I believe. Plain 50 didn't have support on planar. 50Z actually implements most of the controller onboard. Need to scare up a 50Z planar to use that one.

Peter:
   The 50-021 / -031 lacks the ESDI part of the BIOS.

If you pick the 50Z BIOS chips (2 x 512) and split-burn them down into 4 x 256 (as the 50-0xx uses them) you can convert a 50-0xx into an "almost 50Z" without needing the "50-to-50Z upgrade controller", which is a rare item. It only adds the ESDI code to the BIOS and needs a different @DF9F.ADF, which allows to set an address for the BIOS ROM on the controller.

Did that a decade ago and it seemed to work fine with a 50-021 and a 120MB HD from a Mod. 70.

Ed Avis:
   Couldn't you also replace bits of the BIOS in software? Get the BIOS copied into RAM as is sometimes done for performance, then overwrite bits of it. I dunno if anyone has actually done this, but it sounds plausible.

Peter:
   The 286s don't copy the ROM into RAM after POST like the 386s do - and even if: you should do that *before* POST to have the ESDI controller available for the boot process... but I don't think that was what you *meant*.
   [Rem: The "upgrade controller" in fact *does* something similar: it copies some routines into an appropriate area in the "adapter ROM area" (C000 - DFFF) and sets the bootloader entry point to the start of that routine. Usual "check adapter segments for bootable controller ROMs" stuff.]
   Using "Split Copy" on an EPROM programmer is much better. You pick the "even" of the two 27C512 (64K x 8 bit) EPROMs, read and store 0000-7FFF in the first and 8000-FFFF in the second process.
   Then you pick the "odd" EPROM and repeat the step. The four files nicely burn into 4 x 27C256 (32K x 8 bit) EPROMs and you have Odd-Low, Odd-High, Even-Low, Even-High.
It's *a little* complicated - but not much. (Even I've managed...) ;-) I think I still have the codes in my data cemetry somewhere. In the 50-021-format.

The advanced Do-It-Yourselfers *may* pass this obstacle with this method:

  • copy the 50Z-BIOS from 2 x 27C512 into 4 x 27C256 (split the "ODD" and "EVEN" EPROM into ODD-Low and ODD-high, EVEN-low and EVEN-high. 0000h
  • 3FFFh = low, 4000h - 7FFFh = high at each set) This requires an Eprommer!
  • install the new BIOS chipset on the 50-021 planar
  • use the bare "Hardfile Riser card" 90X9441 from the 50Z
  • use any of the IBM ESDI drives (30-160MB)
  • reconfigure the machine. "1 ESDI harddisks" must be displayed in the device-list on advanced diagnostic (unmodified 50-021 show 0 ESDI drives here on that attempt ...)

Tim Clarke:
   [One could also] mod. the planar BIOS to a minimal "IML" Stage 1 subset and add support for a "System Partition" with the "loadable" Stage 2 BIOS on it, then you can mod. the Stage-2 code to your heart's content. Not for the faint-hearted, however.

Content created and/or collected by:
Louis Ohland, Peter Wendt, William Walsh, Kevin Bowling, Jim Shorney, Tim Clarke, David Beem, Tatsuo Sunagawa, Tomáš Slavotínek, and many others.

Ardent Tool of Capitalism - MAD Edition! is maintained by Tomáš Slavotínek.
Last update: 03 Mar 2021 - Changes & Credits | Legal Info & Contact